Turbocharger testing bench TURBO BOOST TEST

Professional turbocharger calibration and performance evaluation

Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Equipment set
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Turbocharger testing bench TURBO BOOST TEST
Equipment set

The bench is used to check the supercharger characteristics after a repair of a turbocharger with or without vacuum or electronic control. On the bench it is possible to adjust the geometry of the turbine in dynamic mode, when the shaft is rotating. The N75 valve check function helps find faults in the control of the turbocharger on the vehicle.

Engine repair shops can use this bench for a comprehensive evaluation of the turbocharger's performance before installing it on an engine.

The test bench can be used in turbine tuning and revamping, in the manufacture of hybrid turbines, to check changes in turbine performance after tuning.

WE OFFER A COMPLETE SOLUTION, SUPPORT AND TRAINING WHEN YOU PURCHASE

Our company has a technical support service center. If you have any questions, you can contact us for help.
Commercial offer for the equipment

Leave your request and our manager will get in touch with you to detail the commercial offer preparation.






    Package contents

    The equipment supplied with the machine allows you to install almost the entire range of turbines from modern manufacturers.
     

    SPECIFICATIONS 

    Parameters TURBO BOOST TEST
    The maximum diameter of the compressor wheel, mm 80
    Maximum achievable rotor speed, rpm 300 000
    Required pressure to the pneumatic system, MPa 0,8 – 1,0
    Recommended minimum receiver volume, m3 1,0
    Overall dimensions of the machine (length x width x height), mm 780 х 1120 х 1274
    Machine weight, kg (approximately) 285
    Power supply parameters 380V ± 10%, 3 Ph, 50Hz ± 1
    Power consumption, not less than kW 1,5
    Balancing system of the machine Boost Test
    Foundation requirements The machine is installed on a conventional hard floor in a workshop.

    SUPPORT AND TRAINING WHEN YOU PURCHASE

    Our company has a technical support service centre. If you have any questions, you can contact us for help.

    Balancing technology
    We help you create and master the balancing technology for your parts
    Personnel training
    We train personnel how to operate the machine
    Warranty
    We provide warranty for all our equipment
    Request a quote for equipment
    Our manager will contact you to find a customized solution.
    Submit a request

    LEARN MORE ABOUT OTHER MACHINES IN THE SERIES

    Balancing machine for turbocharger's rotors BVI-03-10T

    Balancing turbines' shafts and copressors' wheels
    CHRA TURBO BALANCING MACHINE MODEL DBST-10
    Prebalancing machine for turbocompressors DBST-10

    Slow balancing process of turbocompressors' rotors assembled in the hull
    THE STAND FOR ADJUSTING VARIABLE GEOMETRIES "GEOMET-2000"
    Turbocharger flow bench Geomet-2000

    To configure and check changing geometry of turbocompressors
    Tester of electronic actuators ATP-1000
    The tester of electronic actuators ATP-1000.

    Diagnostics of actuators (electric valves, DC motors ) and VNT turbochargers also boost control solenoids.
    The page lists the characteristics of the basic model of the machine. Almost any parameter(diameter, length, weight, etc.) of the bench can be changed on the customer's request. When ordering the machine, all parameters of the machine will be agreed additionally.